Rental Service Kits
-
2897R – Pulley Puller and Installer
This special kit services a wide range of GM, Ford and Chrysler water
pumps, power steering pumps and alternators with pulleys that are pressed into place.
-
3296R – Ford Fan Clutch Wrench (K-D number 3296, stamped on wrench) (same as SER 3473)
48 mm; Ford 6.9L, 7.3L,
& 7.3L DIT Diesel Engines; 1/2" Square Drive.
-
3421R – Ball Joint Service Kit
Removal & installation of press-fit ball joints
and heavy-duty truck brake anchor pins. (Includes one C-frame press and 3 receiver
tubes and adapters.)
-
3562R – 5 Ton Reversible Gear Puller, 2 or 3 Jaw
Puller offers 2 or 3 jaw options with reversible feature for internal
or external pulling requirements.
-
3573R – Pilot Bearing Puller
Flywheel Pilot Bearing Removal On Automobiles, Trucks &
Tractors.
-
4220R – Micrometer Torque Wrench – 30 to 250 ft/lbs
Wrench uses 1/2 inch drive for torque ranges up to 250 ft/lbs. Audible
click when proper torque is reached.
-
41630R – Bearing Race / Seal Installer
Install tapered bearing races and oil seals without damaging
component or housing.
-
41700R – Slide Hammer Puller Set
Includes 5 lb slide hammer for easy removal of wheel hubs and other
applications where the added force is needed. Includes reversible 2 or 3 jaw puller, hub
pullers.
-
41860R – Double Flaring Tool Kit (same as SER 41860, stocked on tool tree)
Double flaring tool for tubing sizes 3/16, 1/4, 5/16, 3/8, & 1/2
inches. 45 degree flare. NOT for stainless steel tubing.
-
62323R – Brake Service Kit
Drum brake spring, pliers, disc brake piston tools, pad separator, Hex
& Torx sockets.
-
62324R – Axle Nut Sockets
Four most popular sizes, 30mm, 32mm, 34mm, 36mm.
-
62325R – Spindle Nut Sockets
Four wheel drive sizes for Ford, Chevy, GMC, Dodge trucks and
others.
-
62326R – Suspension Service Kit
Ball joint and tie rod separators. Pitman arm pullers. Tie rod
adjusting tool.
-
62328R – MacPherson Strut Spring Compressor
Needed for removal of springs and shock absorbers.
-
62329R – Coil Spring Compressor
For wire springs with diameter of 5-5/8 or less.
-
62330R – Serpentine Belt Tool Kit
Sockets and extensions that allow for easy access to hold tension
arm during installation and removal.
-
62331R – Fan Clutch Tool Kit
Includes universal holding
tool to retain fan clutch while removing hub nut.
-
62332R – Harmonic Balancer Remover
Puller removes balancers, pulleys and gears with tapped holes.
A floating swivel prevents damage to the shaft end. Tool bolts to balancer with center screw on
the end of crankshaft.
-
62335R – A/C and Fuel Line Quick Disconnect Kit
Includes coupling tools to disconnect both fuel line and air
conditioning lines with quick disconnects. Special sizes for easy access.
-
62338R – Steering Wheel Puller Kit
Kit includes lock plate remover for GM, Ford vehicles and steering
wheel puller for most cars with pressed on and bolted steering wheels.
-
62340R – 7 Ton Reversible Gear Puller, 2 or 3 Jaw
Puller offers 2 or 3 jaw options with reversible feature for internal
or external pulling requirements.
-
775-9092R – Macpherson Strut Spring Compressor
Needed for removal of springs and shock absorbers.